Hotline: 86-755-61559098
Language

News

News
Recommended / Products
发布时间: 2017 - 11 - 26
7W 6V Portable Flexible Solar Charger with USB port for Electrical DevicesFeatures: l  Environmental protection, free power from the sun, go green!l  Easy to use, connect the USB port with your device by the power cord.l  High transformation efficiency, the efficiency can up to 25 percent.l  Fast charging time, power bank can be full charged within very short time in sunny day.l  Easy to carry, portable eyeholes design makes it suitable for outdoor activities.l  Wide application, it can be used to charge electrical devices, such as smart phone, power banks and other gadgets.l  Durable, water-resistant and long lifespan.l  CE, RoHS and FCC certificates.l  Accept OEM and ODM.
发布时间: 2018 - 03 - 13
Foldable 36W 5V Solar Pack Charger with USB port for outdoor activities                   Features: Environmental protection, free power from the sun, go green!Easy to use, connect the USB port with your device by the power cord.High transformation efficiency, the efficiency can up to 25 percent.Fast charging time, power bank can be full charged within very short time in sunny day.Easy to carry, portable and folded packing design makes it suitable for outdoor activities.Wide application, it can be used to charge electrical devices, such as smart phone, power banks and other gadgets.The Charging temperature is -20 -70 degree centigrade.Durable, water-resistant and long lifespan.CE, RoHS and FCC certificates.Accept OEM and ODM.Specificat...
发布时间: 2018 - 04 - 05
Portable Fashion Hiking Backpack with Solar Charger  Features:Portable design makes it suitable for outdoor activities, such as hiking, camping, travel, etc.Easy to carry, can be installed on the pull rod, travel becomes easier.USB output design, fast charging time. Usually the power bank can be full charged within a very short time in sunny day.Large capacity, special inner design. Can be easily put into a laptop, magazine, camera and other belongings.Concealed Zipper Design, for a safety travelling.Durable, waterproof and long lifespan. Canvas and leather material.CE, RoHS and FCC certificates.Accept OEM and ODM.    Specifications: Canvas and leather materialsLining: Dacron44cm (H) x 15cm (L) x 32cm(W)Solar Panel: 7W 5V Sunpower solar cellsMaximum Wattage: 7...
发布时间: 2018 - 08 - 01
Jinhom Solar 4 Watt Solar Bag with USB PortFeatures: Compact sling bag and Super light weight.Colors optional or customize.Environment friendly, go green!Highly Durable, Abrasion Resistant.Perfect cross body pack for daily use.An every day carry, not a burden to carry.The belt stretches 95cm fully.Adjustable strap, fit comfortably on any person.ETFE laminated Solar Charger, Maximum 4 Watt.You can sling it over your shoulder or across your body.USB 5V 2.1A Output. Compatible with most of USB gadgets.Three main zippered compartments, perfect for cards, keys, Sunglass, wallet and phone, headphones, sunscreen, etc.Package includes: 4 Watt Solar Bag x 1pc Specifications:Canvas materials or custom madeLining: DacronSolar Panel Surface: ETFE LaminatedDimensions: 28cm (H) x 18cm (L) x 9c...
发布时间: 2018 - 05 - 10
Portable 5W 5V Mini Monocrystalline Solar Charger Product DescriptionFeatures: 1,Integrated Molding Technology, without glass.                                                              2,High Transformation Efficiency, Fast Charging.                                      3,Surge protection technology keeps you and your devices safe.                                                           ...
发布时间: 2018 - 05 - 02
Foldable 42W Sunpower Solar Charger with 18V DC & 5V USB Outputs for LaptopProduct DescriptionFeatures: l  Integrated Molding Technology, Slight Curves Available.l  High transformation efficiency, the Sunpower Solar Cell efficiency can up to 25 percent.l  Fast charging time, power bank can be full charged within 2-3 hours in sunny day.l  Easy to carry, portable eyeholes and folded packing design makes it suitable for outdoor activities.l  Surge Protection Technology keeps you and your devices safe.l  Wide application, it can be used to charge electrical devices, such as laptop, smart phone, power banks and other gadgets.l  The Charging temperature is -20 -70 degree centigrade.l  Durable, water-resistant and long lifespan.l  CE, RoHS and...
发布时间: 2018 - 05 - 02
Portable Foldable 200w Sunpower Solar Charger with Dual OutputsProduct DescriptionFeatures: Environmental protection, free power from the sun, go green!High transformation efficiency, our Sunpower monocrystalline silicon efficiency can up to 25 percent.Light and Thin, easy to use, carry, hang and install.Wide application, suitable for Car Batteries, Car, RV, Boat, Ship, Aircraft, Satellites, Space Stations, outdoor breeding, planting, tourism, solar street lamp.The Charging temperature is -20-70 degree centigrade.Dual Outputs, USB 5V and 18V DCShort Cuicuit and surge protection technology keep you and your devices safe.Durable, water-resistant and long lifespan.CE, RoHS and FCC certificates.Can be customized. Specifications: Maximum Power (Pmax):  200WMaximum Power Volt...
发布时间: 2018 - 05 - 01
Folded 12W 5V Solar Panel Charger with USB port for mobile phone Product Description Features: l  Environmental protection, free power from the sun, go green!l  Easy to use, connect the USB port with your device by the power cord.l  High transformation efficiency, the efficiency can up to 25 percent.l  Fast charging time, power bank can be full charged within very short time in sunny day.l  Easy to carry, portable and folded packing design makes it suitable for outdoor activities.l  Wide application, it can be used to charge electrical devices, such as smart phone, power banks and other gadgets.l  The Charging temperature is -20 -70 degree centigrade.l  Durable, water-resistant and long lifespan....
发布时间: 2018 - 05 - 01
Portable 20W Mono Solar Panel Charger with Dual OutputsProduct DescriptionFeatures: Environmental protection, free power from the sun, go green!High transformation efficiency, our monocrystalline silicon efficiency can up to 20 percent.Light and Thin, easy to use and carry.Wide application, suitable for laptops, Car Batteries, Car, RV, Boat, Ship, Aircraft, Satellites, Space Stations, outdoor breeding, planting, tourism, solar street lamp.The Charging temperature is -20-70 degree centigrade.Flexible Solar Panel, A maximum 30 degree arc bendable.Short Cuicuit and surge protection technology keep you and your devices safe.Durable, water-resistant and long lifespan.CE, RoHS and FCC certificates.Can be customized.
News News detail

How does solar panel work?

Date: 2018-11-14
View: 5
From:

How do Solar Panels Work? First let us Introduce the working principle of solar panels, with the global energy increasingly tense, solar energy as a new energy has been vigorously developed, in which we use the most in life is solar cells. Solar cells are mainly made of semiconductor materials. Photoelectric conversion occurs when photoelectric materials absorb light energy to produce current.



What is the working principle of solar cells? Solar cells are devices that directly convert sunlight energy into electricity through photoelectric or photochemical effects. When sunlight shines on a semiconductor, some of it is reflected off the surface and the rest is absorbed or transmitted by the semiconductor. Some of the absorbed light, of course, becomes hot, while others collide with the valence electrons of the atoms that make up the semiconductor, producing electron-hole pairs. In this way, light energy is converted into electric energy by the form of electron hole pairs.

1, The physical basis of solar cells

When the sun illuminates the p-n junction, the electrons in the semiconductor emit electrons because they have obtained the light energy, and the electron-hole pairs are produced accordingly. Under the action of the barrier electric field, the electrons are driven to the type region, and the holes are driven to the P type region, so that there are surplus electrons in the area, and there are surplus holes in the P region. Thus, the photoelectric field opposite to the potential electric field is formed near the p-n junction.

If a P-N junction exists in a semiconductor, a barrier electric field will be formed at both sides of the P-N junction, which can drive electrons to the N region and holes to the P region. As a result, there are surplus electrons in the N region and holes in the P region.

There are more than ten kinds of semiconductor materials that make solar cells, so there are many kinds of solar cells. At present, the most mature and commercially valuable solar cell is silicon solar cell. Next, we take silicon solar cell as an example to introduce in detail the working principle of solar cells.

1). Intrinsic semiconductor

The conductivity of matter depends on the atomic structure. Conductors are generally low-valent elements, and their outermost electrons easily break away from the nucleus and become free electrons. Under the action of an external electric field, they produce directional movement, forming an electric current. High-valent elements (such as inert gases) or polymers (such as rubber), their outermost electrons are strongly bound by the nucleus, it is difficult to become free electrons, so conductivity is very poor, become insulators. Silicon (Si) and germanium (Ge) are tetravalent elements, and their outermost electrons are neither as easily free from the bonds of nuclei as conductors, nor as tightly bound by nuclei as insulators, so their conductivity is between them.

A pure semiconductor is made into a single crystal through a certain process, namely an intrinsic semiconductor. Atoms in crystals form orderly arrays in space, and adjacent atoms form covalent bonds.

Covalent bonds in crystals have strong binding force, so at room temperature, only a few valence electrons get enough energy due to thermal motion (thermal excitation), thus breaking the bond into free electrons. At the same time, a hole is left in the covalent bond. The atom is positively charged by losing a valence electron, or the hole is positively charged. In intrinsic semiconductors, free electrons and holes appear in pairs, that is, the number of free electrons and holes is equal.

If free electrons meet holes in the process of motion, they will fill holes and disappear at the same time. This phenomenon is called recombination. At a certain temperature, the number of pairs of free electrons and holes produced by the intrinsic excitation is equal to the number of pairs of compound free electrons and holes, so the dynamic equilibrium is achieved.

Band theory:

a,When the electrons in a single atom move around the nucleus, the electrons in each orbit have their own specific energy.

b, The closer to the nuclear orbit, the lower the electron energy.

c, According to the principle of minimum energy, electrons always occupy the lowest level of energy.

d, The energy band occupied by valence electrons is called the valence band.

e, There is a forbidden band above the valence band. There is no energy level occupied by electrons in the forbidden band.

f, Above the forbidden band is the conduction band. The energy level in the conduction band is the energy level that the valence electron can occupy when it breaks away from the covalent bond.

g, The forbidden band width is expressed by Eg, and its value is related to the material and temperature of semiconductor. T=300K, Eg=1.1eV of silicon, Eg=0.72eV of germanium.

2). Impurity semiconductor

Impurity Semiconductor: Impurity Semiconductor can be obtained by adding a small amount of impurity elements into the intrinsic semiconductor through diffusion process.

N-type and P-type semiconductors can be formed according to the impurity elements doped, and the conductivity of the impurity semiconductors can be controlled by controlling the concentration of the impurity elements doped.

N-type semiconductors: N-type semiconductors are formed by adding pentavalent elements (such as phosphorus) to pure silicon crystals to replace silicon atoms in the lattice.

Because the impurity atom has five valence electrons in its outermost layer, it has one more electron besides forming a covalent bond with the silicon atom around it. The electrons are free from covalent bonds and become free electrons. In N-type semiconductors, the concentration of free electrons is higher than that of holes, so the free electrons are called majority carriers and the holes are minority carriers. Because impurity atoms can provide electrons, they are called donor atoms.

P-type semiconductors: pure silicon crystals doped with trivalent elements (such as boron), so that it replaces the position of silicon atoms in the lattice, the formation of a P-type semiconductor.

Because the outermost layer of the impurity atom has three valence electrons, when they form a covalent bond with the surrounding silicon atom, a “vacancy” is created, and when the outermost layer of the silicon atom fills the vacancy, a hole is created in the covalent bond. Therefore, in P semiconductor, holes are many and free electrons are few. Because the vacancies in impurity atoms absorb electrons, they are called acceptor atoms.

3). PN junction

PN junction: PN junction is formed at the interface of P-type semiconductor and N-type semiconductor fabricated on the same silicon wafer by different doping process.

Diffusion motion: A substance always moves from a place of high concentration to a place of low concentration. This motion due to the difference in concentration is called diffusion motion.

When a P-type semiconductor and an N-type semiconductor are fabricated together, the concentration of the two carriers varies greatly at their interfaces, so the hole in the P-region must diffuse to the N-region. Meanwhile, the free electrons in the N-region must diffuse to the P-region, as shown in the figure.

Because the free electrons diffused into the P region recombine with the holes, and the holes diffused into the N region recombine with the free electrons, the concentration of many electrons decreases near the interface, the negative ion region appears in the P region, and the positive ion region appears in the N region. They can’t move, which is called the space charge region, thus forming the built-in electric field-epSILon;.

As the diffusion proceeds, the space charge region widens and the built-in electric field strengthens. The direction of the built-in electric field points from the N region to the P region, which prevents the diffusion from proceeding.

Drift motion: under the action of electric field force, the motion of carriers is called drift motion.

When the space charge region is formed, the minority carrier drifts, the hole moves from the N region to the P region, and the free electron moves from the P region to the N region. In the absence of an external electric field and other excitations, the number of multiple particles participating in the diffusion motion is equal to the number of few particles participating in the drift motion, thus achieving a dynamic equilibrium and forming a PN junction, as shown in the figure. At this time, the space charge region has a certain width, the potential difference is =Uho, and the current is zero.

2, the principle of solar cells

1). Photovoltaic effect:

The photovoltaic energy conversion of solar cells is based on the photovoltaic effect of semiconductor pn junction. As mentioned earlier, photons with energy greater than the silicon forbidden band pass through the antireflective film into silicon when illuminated by a semiconductor photovoltaic device, and photogenerated electron-hole pairs are excited in N, depletion and P regions.

Depletion Zone: The photogenerated electron-hole pairs are separated by the built-in electric field immediately after they are generated in the depletion zone. The photogenerated electrons are fed into the N zone and the photogenerated holes are pushed into the P zone. According to the depletion approximation condition, the carrier concentration at the boundary of the depletion region is approximately 0, that is, p=n=0.

In the N region, the photogenerated holes diffuse to the P-N junction boundary after the photogenerated electron-hole pairs are formed. Once they reach the P-N junction boundary, they are immediately affected by the built-in electric field. They are pulled by the electric field force and drift across the depletion region into the P region. The photogenerated electrons (polyelectrons) are left in the N region.

In the P region, photogenerated electrons (minority electrons) enter the N region first because of diffusion and then because of drift, and photogenerated holes (polyelectrons) remain in the P region. The accumulation of positive and negative charges on both sides of the P-N junction results in the storage of excess electrons in the N region and the remaining holes in the P region. Thus forming a photoelectric field opposite to the built-in electric field.

a, In addition to partially counteracting the effect of the barrier electric field, the photovoltaic field also makes the P region positive and the N region negative, and the electromotive force is generated in the thin layer between the N region and the P region, which is called photovoltaic effect. When the battery is connected to a load, the photocurrent flows from the P region to the N region through the load, and the power output is obtained from the load.

b, If the ends of P-N junctions are opened, the electromotive force can be measured, which is called open circuit voltage Uoc. For crystalline silicon batteries, the typical value of open circuit voltage is 0.5 ~ 0.6V.

c, If the external circuit is short-circuited, there is a current in the external circuit which is proportional to the incident light energy. This current is called short-circuit current Isc.

Factors affecting photocurrent:

a, The more electron hole pairs produced by light in the interface layer, the greater the current.

b, The more light energy the interfacial layer absorbs, the larger the area of the interfacial layer, i.e. the cell, and the larger the current formed in the solar cell.

c, Photoinduced carriers can be generated in the N region, depletion region and P region of solar cells.

d, The photogenerated carriers in each region must pass through the depletion region before recombination to contribute to the optical current. Therefore, the generation and recombination, diffusion and drift in each region must be taken into account in solving the actual photogenerated current.

Equivalent circuit, output power and fill factor of solar cells

A,Equivalent circuit

In order to describe the working state of the battery, the battery and load system are often simulated by an equivalent circuit.

a, Constant Current Source: Under constant illumination, a working solar cell, its photocurrent does not change with the working state, in the equivalent circuit can be regarded as a constant current source.

b, Dark current Ibk: A part of the photocurrent flows through the load RL, and a terminal voltage U is established at both ends of the load. In turn, it is positively biased in the PN junction, causing a dark current Ibk opposite to the optical current.

c, In this way, the equivalent circuit of an ideal PN homogenous junction solar cell is plotted as shown in the figure.

d, Series resistance RS: Because the front and back electrodes contact, and the material itself has a certain resistivity, base and top layer are inevitably introduced additional resistance. The current flowing through the load will inevitably cause loss when passing through them. In the equivalent circuit, the total effect can be represented by a series resistance RS.

e, Parallel resistance RSh: Because of the leakage of the battery edge and the metal bridge formed at the cracks and scratches when making the metallized electrode, the part of the current should be short-circuited through the load. This effect can be equivalent to a parallel resistance RSh.

When the current flowing into the load RL is I and the terminal voltage of the load RL is U, it can be obtained:

How does solar panel work?

The P in the formula is the output power of the solar cell irradiated on the load RL.

B, Output power

When the current flowing into the load RL is I and the terminal voltage of the load RL is U, it can be obtained:

The P in the formula is the output power of the solar cell irradiated on the load RL.

When the load RL changes from 0 to infinity, the output voltage U changes from 0 to U0C, and the output current changes from ISC to 0. Thus the load characteristic curve of solar cells can be drawn. Any point on the curve is called the working point. The connection between the working point and the origin is called the load line. The reciprocal of the slope of the load line is equal to RL. The horizontal and vertical coordinates corresponding to the working point are the working voltage and the working current.

When the load resistance RL is adjusted to a certain value Rm, a point M is obtained on the curve. The product of the corresponding working current Im and the working voltage Um is the largest, that is, Pm = ImUm.

Generally speaking, M point is the best working point (or maximum power point), Im is the best working current, Um is the best working voltage, Rm is the best load resistance, and Pm is the maximum output power.

C,Fill factor

a, The ratio of maximum output power to (Uoc *Isc) is called fill factor (FF), which is one of the important indicators to measure the output characteristics of solar cells.

b, Filling factor characterizes the quality of solar cells. Under certain spectral irradiance, the larger the FF, the more square the curve, and the higher the output power.

D, solar cell efficiency, factors affecting efficiency

(1). Solar cell efficiency:

When a solar cell is irradiated, the ratio of the output power to the incident light power is called the efficiency of the solar cell, also known as the photoelectric conversion efficiency. Generally refers to the maximum energy conversion efficiency when the external circuit is connected with the best load resistance RL.

In the above formula, if Ats are replaced by Aa (also called active area), that is, the area of grid lines is deducted from the total area, so the calculation efficiency is higher. This should be noted when reading the literature at home and abroad.

Prince of the United States first calculated the theoretical efficiency of silicon solar cells by 21.7%. In the 1970s, M. Wolf discussed it in detail. He also found that the theoretical efficiency of silicon solar cells was 20% ~ 22% under the AM0 spectral condition, and then modified it to 25% (AM1.0 spectral condition).

To estimate the theoretical efficiency of a solar cell, all possible losses from incident light to output power must be taken into account. Some of these losses are related to materials and processes, while others are determined by basic physical principles.

(2), Factors affecting efficiency

To sum up, the open-circuit voltage Uoc, short-circuit current ISC and filling factor FF must be increased to improve the efficiency of solar cells. These three parameters are often mutually constrained, if unilaterally increased one of them, may therefore reduce the other, so that the total efficiency not only did not improve but also decreased. Therefore, the material and design process must be considered in a comprehensive way so as to maximize the product of the 3 parameters.

1). Material band width:

The open-circuit voltage UOC increases with the increase of bandwidth Eg, but the short-circuit current density decreases with the increase of bandwidth Eg. As a result, the peak of solar cell efficiency can be expected at a certain Eg. The solar cells with Eg value of 1.2 ~ 1.6eV can be expected to achieve the highest efficiency. Direct bandgap semiconductors for thin film batteries are preferable because they can absorb photons near the surface.

2). Temperature:

The diffusion length of minority carrier increases slightly with the increase of temperature, so the photocurrent increases with the increase of temperature, but the UOC decreases sharply with the increase of temperature. The filling factor decreases, so the conversion efficiency decreases with the increase of temperature.

3). Irradiance:

With the increase of irradiance, the short-circuit current increases linearly and the maximum power increases. Focusing sunlight on solar cells can make a small solar cell generate a lot of electricity.

4). Doping concentration:

Another factor that has a significant effect on UOC is the doping concentration of semiconductors. The higher the doping concentration is, the higher the UOC is. However, when the concentration of impurities in silicon is higher than 1018/cm3, it is called high doping effect. The phenomenon of band gap contraction, impurity ionization and minority carrier lifetime decrease caused by high doping should also be avoided.

5). Photoinduced carrier recombination lifetime:

For semiconductor solar cells, the longer the recombination life of photogenerated carriers, the greater the short-circuit current. The key to long life is to avoid the formation of composite centers in the process of material preparation and battery production. The composite center can be removed and the service life can be prolonged by proper and frequent processing.

6). Surface recombination rate:

Low surface recombination rate helps to increase Isc. It is difficult to measure the recombination rate of the front surface and is often assumed to be infinite. A battery called the Back Electric Field (BSF) is designed to diffuse a P + layer on the back of the battery before depositing metal contact.

7). Series resistance and metal grating:

Series resistance comes from the resistance of lead wire, metal contact grid or battery body, and metal grid can not pass through the sun. In order to maximize the Isc, the area occupied by the metal grid should be the smallest. Generally, the metal grid is made into a dense and thin shape, which can reduce the series resistance and increase the light transmission area of the battery.

8). Use suede batteries to design and select high quality antireflection coatings.

Relying on the pyramid-shaped square cone structure of the surface, the multiple reflection of light not only reduces the loss of reflection, but also changes the direction of light in silicon and prolongs the light path, thus increasing the yield of photogenerated carriers; the zigzag surface also increases the area of PN junction, thus increasing the collection rate of photogenerated carriers and short-circuit current. Increase 5% to 10% and improve the red light response of the battery.

9). Effect of shadow on solar cells:

Solar cells will cause uneven illumination due to shadow occlusion and so on, and the output power will be greatly reduced.

At present, the application of solar cells has entered industries, commerce, agriculture, communications, household appliances and public utilities from the military and aerospace fields, especially in remote areas, mountains, deserts, islands and rural areas, to save expensive transmission lines. But at this stage, the cost is still high, and it costs tens of thousands of dollars to send out a kilowatt of electricity, so large-scale use is still economically constrained.

However, in the long run, with the improvement of solar cell manufacturing technology and the invention of new photoelectric conversion devices, the protection of the environment and the huge demand for renewable and clean energy in various countries, solar cells will still be a more practical way to utilize solar radiation energy, and can be used in large-scale for human beings in the future. It can open up broad prospects.How does solar panel work?

If you have any questions about this article “How do Solar Panels Work“, please just feel free to contact us.



News / Recommending news
2018 - 11 - 29
点击次数: 11
Before let you know how to make a solar panel, let us understand “What are solar panels?”Solar panels use silicone cells to capture sunlight and turn the electrons into energy which we ...
2018 - 11 - 14
点击次数: 5
How do Solar Panels Work? First let us Introduce the working principle of solar panels, with the global energy increasingly tense, solar energy as a new energy has been vigorously developed, in w...
2018 - 07 - 31
点击次数: 329
An Australian physicist is leading a push to pioneer a new type of low-cost solar energy he believes could make signing up for energy accounts as straightforward as taking up a mobile phone plan.In Ma...
2018 - 07 - 29
点击次数: 28
This roof in Newcastle has become the first in Australia to be covered with specially printed solar cells. Credit: University of Newcastle, Author providedAustralia's first commercial installation of ...
2018 - 04 - 17
点击次数: 21
China’s emergence as a global leader of investment in clean energy projects poses serious threat to U.S based operators for the Alternative Energy industry. China has been a frontrunner in terms of so...
  • Related news / News More
  • 点击次数: 11
    2018 - 11 - 29
    Before let you know how to make a solar panel, let us understand “What are solar panels?”Solar panels use silicone cells to capture sunlight and turn the electrons into energy which we can use for electricity. With so many methods for generating electricity either through renewable or non-renewable methods, solar panels are a fantastic way to utilize earths free access to energy since the sun tends to provide us with more energy than our planet needs.Okay, so back to “How to Make a Solar Panel”, there are several steps.Step 1, Shop for and buy the silicon cells. There are many types of solar cells with different efficiency on the markets, usually we choose mono-crystalline solar cells for small wattage applications, the cell size is 125mm x 125mm, 3.2 Watt per cell...
  • 点击次数: 5
    2018 - 11 - 14
    How do Solar Panels Work? First let us Introduce the working principle of solar panels, with the global energy increasingly tense, solar energy as a new energy has been vigorously developed, in which we use the most in life is solar cells. Solar cells are mainly made of semiconductor materials. Photoelectric conversion occurs when photoelectric materials absorb light energy to produce current.What is the working principle of solar cells? Solar cells are devices that directly convert sunlight energy into electricity through photoelectric or photochemical effects. When sunlight shines on a semiconductor, some of it is reflected off the surface and the rest is absorbed or transmitted by the semiconductor. Some of the absorbed light, of course, becomes hot, while others collide with ...
  • 点击次数: 329
    2018 - 07 - 31
    An Australian physicist is leading a push to pioneer a new type of low-cost solar energy he believes could make signing up for energy accounts as straightforward as taking up a mobile phone plan.In May last year, the University of Newcastle professor Paul Dastoor used organic printed solar cells to power screens and displays at an exhibition in Melbourne.Related: Subsidies for new household solar panels to end next yearLess than one millimetre thick and held down with double-sided sticky tape, the panels are similar in texture to a potato chip packet and can be produced for less than $10 per square metre.Dastoor has been working on the technology for more than a decade, but has now begun a 200 square-metre installation – the first commercial application of its kind in Australia and po...
  • 点击次数: 28
    2018 - 07 - 29
    This roof in Newcastle has become the first in Australia to be covered with specially printed solar cells. Credit: University of Newcastle, Author providedAustralia's first commercial installation of printed solar cells, made using specialised semiconducting inks and printed using a conventional reel-to-reel printer, has been installed on a factory roof in Newcastle. The 200 square metre array was installed in just one day by a team of five people. No other energy solution is as lightweight, as quick to manufacture, or as easy to install on this scale.Our research team manufactured the solar modules using standard printing techniques; in fact, the machine that we use typically makes wine labels. Each solar cell consists of several individual layers printed on top of each other, which ...
  • 点击次数: 21
    2018 - 04 - 17
    China’s emergence as a global leader of investment in clean energy projects poses serious threat to U.S based operators for the Alternative Energy industry. China has been a frontrunner in terms of solar module manufacturing and it has made substantial wind power investments in 2017 to expand its renewables footprint worldwide. " data-reactid="22" style="margin-top: 0px; margin-bottom: 1em; color: rgb(0, 0, 0); font-family: Georgia, 'Times New Roman', serif; font-size: 18px; orphans: 2; white-space: normal; widows: 2; background-color: rgb(255, 255, 255);"China’s emergence as a global leader of investment in clean energy projects poses serious threat to U.S based operators for the Alternative Energy industry. China has been a frontrunner in terms of solar module ma...
Copyright ©2005 - 2013 Shenzhen Jinhom Solar Technology Co., Ltd
犀牛云提供企业云服务